Touch one machine fault analysis and solution (1)
Touch integrated machine is a display device that integrates display and touch control. It is widely used in retail service industry, municipal, public places, financial institutions and other places, and is a typical representative of human-computer interaction.
However, the touch-one machine itself is a liquid crystal display-based display device, and with its touch function, the failure and breakage rate are relatively high compared to other advertising machines, and for basic fault problems, users What should I do in peacetime?
Touch one machine fault analysis and solution:
1. Fault phenomenon: long response time
After touching the display screen with your finger, it takes a long time to react.
Fault analysis and solution:
The first reason is that there is a moving water droplet on the touch one machine, just wipe it with a dry soft cloth. Cause two: The host configuration is too low, such as the clock frequency is too low. If this is the case, it is best to replace the host.
2. Fault phenomenon: local non-response
After touching the monitor screen with your finger, there is no response in the local area.
Fault analysis and solution:
The first reason is that the reflective stripe of the touch-one machine is partially covered, and it can be wiped clean with a dry soft cloth. Reason 2: The reflection stripe is partially scraped off by the hard object. In this case, the advertising machine will not be repaired and can only be returned to the manufacturer for disposal by the manufacturer.
3. Symptom: The system is not working properly
Touching the all-in-one itself is normal, but after connecting to the host, the computer cannot operate.
Fault analysis and solution:
Cause one: Before the host starts loading the touch-one machine driver, the touch-one machine control card receives the operation signal, and only needs to restart the computer after restarting the power-off. Cause two: The driver version of the touch all-in-one is too low and you need to install the latest driver.
4. Fault scene: touch deviation
The position touched by the finger does not coincide with the mouse arrow.
Fault analysis and solution:
After the driver is installed, there is no vertical touch to the center of the bull's-eye when the correction position is made. Solution: Recalibrate the position.
-------------------------------------------------- -------------------------------
Recommended related products
KONWHAI -- Touch Screen kiosk, click to enter to understand
KONWHAI -- LCD advertising machine, click to enter to understand
KONWHAI -- Smart meeting whiteboard, click to enter to understand
Official website: www.kwhtouch.com
-------------------------------------------------- -------------------------------
However, the touch-one machine itself is a liquid crystal display-based display device, and with its touch function, the failure and breakage rate are relatively high compared to other advertising machines, and for basic fault problems, users What should I do in peacetime?
Touch one machine fault analysis and solution:
1. Fault phenomenon: long response time
After touching the display screen with your finger, it takes a long time to react.
Fault analysis and solution:
The first reason is that there is a moving water droplet on the touch one machine, just wipe it with a dry soft cloth. Cause two: The host configuration is too low, such as the clock frequency is too low. If this is the case, it is best to replace the host.
2. Fault phenomenon: local non-response
After touching the monitor screen with your finger, there is no response in the local area.
Fault analysis and solution:
The first reason is that the reflective stripe of the touch-one machine is partially covered, and it can be wiped clean with a dry soft cloth. Reason 2: The reflection stripe is partially scraped off by the hard object. In this case, the advertising machine will not be repaired and can only be returned to the manufacturer for disposal by the manufacturer.
3. Symptom: The system is not working properly
Touching the all-in-one itself is normal, but after connecting to the host, the computer cannot operate.
Fault analysis and solution:
Cause one: Before the host starts loading the touch-one machine driver, the touch-one machine control card receives the operation signal, and only needs to restart the computer after restarting the power-off. Cause two: The driver version of the touch all-in-one is too low and you need to install the latest driver.
4. Fault scene: touch deviation
The position touched by the finger does not coincide with the mouse arrow.
Fault analysis and solution:
After the driver is installed, there is no vertical touch to the center of the bull's-eye when the correction position is made. Solution: Recalibrate the position.
-------------------------------------------------- -------------------------------
Recommended related products
KONWHAI -- Touch Screen kiosk, click to enter to understand
KONWHAI -- LCD advertising machine, click to enter to understand
KONWHAI -- Smart meeting whiteboard, click to enter to understand
Official website: www.kwhtouch.com
-------------------------------------------------- -------------------------------
评论
发表评论